Fix Leaky Sink Faucet: DIY Repairs & Expert Tips
Is your kitchen sink faucet leaking? It's a common issue that can waste water and increase your utility bills. Luckily, fixing a leaky faucet is a DIY project that can save you money and time. Let's dive into the world of plumbing and tackle this issue step by step.
Before we begin, it's essential to understand that faucets can leak for various reasons. The most common are worn-out O-rings, corroded valve seats, or loose parts. Depending on the cause, you might need to replace parts or tighten connections. Let's explore the different types of faucets and how to fix their leaks.
Compression Faucets
Compression faucets are the oldest type and have two handles that control the water flow. They work by compressing a rubber washer against the seat to stop the water flow.



Leaks in compression faucets are usually caused by a worn-out washer. Replacing the washer is a straightforward process that only requires a Phillips or flathead screwdriver. Here's how:
Replacing the Washer
1. Turn off the water supply valves under the sink. Open the faucet to relieve any pressure and prevent leaks.



2. Remove the faucet handle using an Allen wrench or a flathead screwdriver. Some handles may require a special tool, so check your faucet's manual.
3. Use a pair of pliers to grip and unscrew the packing nut. This nut secures the stem in place and should unscrew counterclockwise.
4. Pull out the stem and remove the washer. You may need to use needle-nose pliers or tweezers to remove the washer if it's stuck.






5. Take the old washer to a hardware store to find a matching replacement. Insert the new washer and reassemble the faucet in reverse order.
Adjusting the Faucet
While rare, leaks in compression faucets can also be caused by a loose connection. Adjusting the faucet can tighten these connections and stop the leak.
1. Turn off the water supply valves under the sink and open the faucet.

2. Use an adjustable wrench to tighten the packing nut and the faucet's base. Tighten each about a quarter-turn at a time, then check for leaks. If the leak persists, continue tightening until the leak stops, but be careful not to overtighten and strip the faucet.
Ball Faucets
Ball faucets have a single handle that controls both hot and cold water. They work by lifting a ball-shaped rotating plug that allows water to flow through.
Leaks in ball faucets are usually caused by corrosion or wear on the cam washer or the faucet's seat. Replacing these parts can fix the leak. Here's how:
Replacing the Seat and Cam Washer
1. Turn off the water supply valves under the sink and open the faucet.
2. Remove the faucet handle using an Allen wrench or a flathead screwdriver. Some handles may require a special tool, so check your faucet's manual.
3. Remove the cap at the top of the faucet using a pair of pliers. This cap covers the cam and the faucet's seat.
4. Use an adjustable wrench to unscrew the faucet's seat. It should unscrew clockwise. If it's stuck, you may need to use a basin wrench, a tool specifically designed to access hard-to-reach nuts.
5. Pull out the cam using needle-nose pliers or tweezers. Take the faucet's seat and cam to a hardware store to find a matching replacement.
6. Insert the new cam and seat, then reassemble the faucet in reverse order.
Replacing the Faucet's Ball
If replacing the seat and cam washer didn't fix the leak, the ball itself may be worn out. Here's how to replace it:
1. Follow steps 1-4 above to access the faucet's ball.
2. Use a pair of needle-nose pliers or tweezers to remove the faucet's ball. You may need to tap the faucet gently with a hammer to loosen it if it's stuck.
3. Take the old ball to a hardware store to find a matching replacement. Insert the new ball and reassemble the faucet in reverse order.
Cartridge Faucets
Cartridge faucets have a single handle that controls both hot and cold water. They work by lifting a cartridge that controls the water flow through the faucet.
Leaks in cartridge faucets are usually caused by a faulty cartridge. Replacing the cartridge is a straightforward process that typically only requires an Allen wrench. Here's how:
Replacing the Cartridge
1. Turn off the water supply valves under the sink and open the faucet.
2. Remove the faucet handle using an Allen wrench. Some handles may require a special tool, so check your faucet's manual.
3. Remove the cap at the top of the faucet using a pair of pliers. This cap covers the faucet's cartridge.
4. Use an adjustable wrench to unscrew the faucet's cartridge retainer ring. It should unscrew clockwise. If it's stuck, you may need to use a basin wrench.
5. Pull out the faucet's cartridge using needle-nose pliers or tweezers. Take the old cartridge to a hardware store to find a matching replacement.
6. Insert the new cartridge into the faucet and reassemble it in reverse order.
Regular faucet maintenance can prevent leaks and keep your faucets in good working order. Check your faucets regularly for any signs of wear or corrosion, and address any issues promptly to prevent larger problems. If you're unsure about any part of the repair process, don't hesitate to consult a professional plumber.
In many cases, fixing a leaky faucet is a simple and cost-effective DIY project. By understanding the different types of faucets and their components, you can tackle most faucet leaks with confidence. So, grab your toolbox and start saving money and water today!





