Mastering Angles: A Step-by-Step Guide to Cutting Stair Stringers
Building sturdy, safe stairs requires precision in cutting stair stringers. Stringers are the longitudinal support beams that run alongside the stairs, and they bear the brunt of the weight. Cutting angles for stringers might seem daunting, but with the right tools and steps, it's a manageable task. This guide will walks you through the process, ensuring your stairs are not just functional, but also visually appealing and safe.
Before you start, ensure you have the right tools. You'll need a circular saw with a 6-1/2" or 8" blade, a tape measure, a square, a pencil, and some safety gear like goggles and work gloves. Also, you'll need to know the rise and run of your stairs. The rise is the vertical distance between each stair, and the run is the horizontal distance.
Marking and Measuring Stringer Cuts
The first step in cutting angles for stair stringers is marking the stringers where they need to be cut. Start by laying out your stringers on a flat surface. You'll need two for a straight staircase and three or more for L-shaped or U-shaped staircases.



Using your tape measure and square, mark the stringers at the rise-to-run ratio. This is typically 7" for every 11" (a 7:11 ratio), but it might vary based on your specific staircase design. At each mark, use your square to draw a line across the width of the stringer.
CuttingWatch Angles
Once you've marked your cuts, it's time to set up your circular saw. Ensure the blade depth is set correctly - it should extend below the stringer by no more than 1/4". Secure the stringer in place, ensuring it's stable and won't move when you're cutting.



Start cutting from the top of the stringer, moving the saw slowly and steadily. Ensure you're following your mark and cutting through the stringer completely. Be careful at the end of the cut to avoid kickback. Once you've cut through the stringer, you'll have your watch angle, which allows the stringer to sit at the correct angle on your staircase.
CuttingNotch Angles
Next, you'll need to cut notch angles at the end of each stringer. These notches allow the stringers to fit together and provide additional support. Mark the notches at the same ratio as your rise and run.
To cut the notches, you'll need to set the blade depth on your circular saw to about 1/4". Place the stringer in a vise to hold it securely. Start your cut at the top of the mark and move the saw steadily through the stringer. Once you've cut through, you should have a notch at the end of the stringer.





Assembling Your Staircase
With your stringers cut, it's time to assemble your staircase. Start by installing the risers, which are the vertical pieces that separate each step. Install them at the rise-to-run ratio you've calculated.
Next, install the treads, which are the horizontal pieces that you'll actually walk on. Again, they should be installed at the rise-to-run ratio. Ensure each tread is level and properly supported by the stringers.
Attaching Trim
Once all your treads and risers are in place, you can add trim to give your staircase a finished look. This might include stringer facings, nosing, or Cove moulding. Ensure your trim is securely attached and doesn't interfere with the function of your staircase.
Finally, ensure your staircase is safe and functional. Check that each step is level and secure, and that the staircase is properly anchored to the walls and floor. A sturdy, safe staircase is a valuable addition to any home, and with these steps, you're well on your way to building one.
Now that you've cut the angles for your stair stringers and assembled your staircase, it's time to stand back and admire your handiwork. If you've measured and cut accurately, your staircase should be both safe and visually appealing. It's a rewarding feeling to know you've built something that will serve your home well, and these skills can be applied to other DIY projects. So, the next time you're tackling a home improvement project that involves angles and measuring, you'll have the confidence to take it on.





